Subscribe to RSS Feed

Helmets

Switch View

Bonehead Rev2 GoPro Helmet Mount

$40.00

Bonehead Rev2 GoPro Helmet Mount.
Learn More | Add to Wishlist | Add to Compare
Bonehead Rev2 Contour Rail Helmet Mount

$40.00

Bonehead Rev2 Contour Rail Helmet Mount.
Learn More | Add to Wishlist | Add to Compare
Bonehead Cutaway Chincup Kit

$22.00

Chincup Cutaway Mod Kit by Bonehead Composites. This kit Includes the cutaway handle, clips, hardware and mounting instructions.
Learn More | Add to Wishlist | Add to Compare
Bonehead Concealed Chincup

$80.00

The new Concealed Replacement Chincup Assembly from Bonehead Composites. This new chincup kit is made for replacements or retrofits of all Bonehead open-face helmets and can also be used on other manufacturer helmets. This updated concealed version featured a centered concealed pocket to hid the ends of the ladder straps. The padding is also removable for washing.
Learn More | Add to Wishlist | Add to Compare
Bonehead Drawstring Helmet Bag

$12.00

Soft Bonehead Drawstring Helmet Bag for your helmet. This helmet bag from Bonehead is a great carry bag and inexpensive protection for your helmet investment. Fits most helmets.
Learn More | Add to Wishlist | Add to Compare
REvolve Replacement Lens

$27.00

Replacement Lens for the REvolve Helmet by Bonehead Composites. This is an anti-fog coated lens. Specify shell/helmet size above with your order. The REvolve lenses are in stock for immediate shipment from ChutingStar.com. Tinted lenses are expected later this year.
Learn More | Add to Wishlist | Add to Compare
Mamba Replacement Lens

$27.00

Replacement lens for the Mamba full-face helmet by Bonehead Composites. This is a clear Lexan Anti-Fog coated lens. The Mamba replacement lens is always in stock at ChutingStar!
Learn More | Add to Wishlist | Add to Compare
Havok Replacement Lens

$25.00

Replacement lens for the Havok full-face helmet by Bonehead Composites. This is a clear Lexan Anti-Fog coated lens. The Havok replacement lens is always in stock at ChutingStar!
Learn More | Add to Wishlist | Add to Compare
REvolve Contour Camera Mount

$60.00

The REvolve Contour Camera Mount allows you to add the Contour series of cameras to the side of your helmet such as the Contour1080p, ContourGPS or Contour+. Bonehead Composites now offers a mounting solution for the contour camera and standard side mounts. Consists of a plastic Derlin plate and machined aluminum rail which slides into the contour rail guides and allows visor rotation and level adjustments. The REvolve Contour Camera Mount is sized per the shell/visor size. Select your REvolve size above when ordering. Note: Mount does not include Contour camera, which is available separately from ChutingStar.com. Mounting instructions 1. Remove original visor pin from the left side of the helmet. 2. Place a piece of masking tape over each raise mounting pad on the REvolve. 3. Using the longer pin supplied with the contour mount, slide the pin through the upper plate hole through the visor grommet and finally into the helmet and secure. 4. Rotate the plate, centering the middle or each lower mounting slots over the center of each mounting pad. Mark these locations with a pen and then check for center accuracy. 5. Using a 8/32 drill or Dremel tool drill the center marks through the helmet. 6. Secure the lower contour mount with supplied hardware with washers under both the screw head and nut. 7. Minor up/down adjustments can be obtain by loosening the lower screws and slightly rotating the plate to the fore or aft slot positions. Most sizes of the REvolve Contour Camera Mount are in stock for immediate shipment from ChutingStar.com.
Learn More | Add to Wishlist | Add to Compare
Replacement Liner for Mamba

$45.00

Replacement Liner for the Mamba Helmet. There are three shell sizes for the Mamba, so make sure your liner is made for the shell size you have. Replacement liners available is sizes XS-XXL. Shell size 1 can take the XSmall liner. Shell size 2 can take the Small, Medium and Large liners. Shell size 3 can take the XLarge and XXLarge liners. The Bonehead sizing guide can be found at this link. This is a factory replacement liner from Bonehead Composites.
Learn More | Add to Wishlist | Add to Compare
Replacement Top Plate for Flat-Top Pro

$66.00

Replacement top plate for Flat-Top Pro. The top plates, by Bonehead Composites, are made of carbon fiber, and are available in three different sizes.
Learn More | Add to Wishlist | Add to Compare