Helmets

Page:
  1. 1
  2. 2
  1. Bonehead Cordura Two-Helmet Carry Bag

    Bonehead Cordura Two-Helmet Carry Bag

    $40

    Bonehead Cordura Helmet Carry Bag. Bonehead's Cordura Helmet and Accessory Bag has ample amount of space for a Bonehead full-faced helmet and a Bonehead open-faced helmet in the large pocket, which is also large enough to hold a Bonehead Flat Top Camera Helmet. Learn More
  2. Bonehead Drawstring Helmet Bag

    Bonehead Drawstring Helmet Bag

    $12

    Soft Bonehead Drawstring Helmet Bag for your helmet. This helmet bag from Bonehead is a great carry bag and inexpensive protection for your helmet investment. Fits most helmets. Learn More
  3. Rev2 Replacement Lens

    Rev2 Replacement Lens

    $27

    Rev2 Replacement Lens. Learn More
  4. Bonehead Aero Replacement Visor Lens

    Bonehead Aero Replacement Visor Lens

    $42

    Bonehead Aero Replacement Visor Lens. Learn More
  5. Bonehead AERO Rev2 GoPro Helmet Front Mount

    Bonehead AERO Rev2 GoPro Helmet Front Mount

    $40

    Bonehead AERO/Rev2 GoPro Helmet Mount. Learn More
  6. Bonehead Concealed Chincup

    Bonehead Concealed Chincup

    $80

    The new Concealed Replacement Chincup Assembly from Bonehead Composites. This new chincup kit is made for replacements or retrofits of all Bonehead open-face helmets and can also be used on other manufacturer helmets. This updated concealed version featured a centered concealed pocket to hid the ends of the ladder straps. The padding is also removable for washing. Learn More
  7. REvolve Replacement Lens

    REvolve Replacement Lens

    $27

    Replacement Lens for the REvolve Helmet by Bonehead Composites. This is an anti-fog coated lens. Specify shell/helmet size above with your order. The REvolve lenses are in stock for immediate shipment from ChutingStar.com. Tinted lenses are expected later this year. Learn More
  8. REvolve Contour Camera Mount

    REvolve Contour Camera Mount

    $60

    The REvolve Contour Camera Mount allows you to add the Contour series of cameras to the side of your helmet such as the Contour1080p, ContourGPS or Contour+. Bonehead Composites now offers a mounting solution for the contour camera and standard side mounts. Consists of a plastic Derlin plate and machined aluminum rail which slides into the contour rail guides and allows visor rotation and level adjustments. The REvolve Contour Camera Mount is sized per the shell/visor size. Select your REvolve size above when ordering. Note: Mount does not include Contour camera, which is available separately from ChutingStar.com. Mounting instructions 1. Remove original visor pin from the left side of the helmet. 2. Place a piece of masking tape over each raise mounting pad on the REvolve. 3. Using the longer pin supplied with the contour mount, slide the pin through the upper plate hole through the visor grommet and finally into the helmet and secure. 4. Rotate the plate, centering the middle or each lower mounting slots over the center of each mounting pad. Mark these locations with a pen and then check for center accuracy. 5. Using a 8/32 drill or Dremel tool drill the center marks through the helmet. 6. Secure the lower contour mount with supplied hardware with washers under both the screw head and nut. 7. Minor up/down adjustments can be obtain by loosening the lower screws and slightly rotating the plate to the fore or aft slot positions. Most sizes of the REvolve Contour Camera Mount are in stock for immediate shipment from ChutingStar.com. Learn More
  9. Bonehead Aero Contour Rail Helmet Mount

    Bonehead Aero Contour Rail Helmet Mount

    $45

    Bonehead Aero Contour Rail Helmet Mount. Learn More
  10. Bonehead Bonepad Flat-Top Helmet Liner Insert

    Bonehead Bonepad Flat-Top Helmet Liner Insert

    $15

    Bonehead Bonepad Flat-Top Helmet Liner Insert Learn More
Page:
  1. 1
  2. 2