ChutingStar Skydive & Skate Gear Superstore!
Looking for the Skate Shop?
WRYD Telescoping GoPro Camera Pole
GoPro Sportsman Mount
Dakine Deluxe POV Camera Case
Floydie Pro II Double GoPro HERO3/3+ Handcam Glove
GoPro 3-Way Mount
GoPro Bodyboard Mount
GoPro HERO3/3+ Protective Lenses
GoPro HERO3/3+ The New Frame Package
GoPro Dual HERO3+ System
Sony Action Cam Original Waterproof Housing
GoPro Floydie Wave 360 Hand Mount
UKPro Dual GoPro Flex Grip
UKPro GoPro 54HD Telescoping Camera Pole
UKPro POV20-LT Soft GoPro Camera Case
GoPro HERO3/3+ Dive Housing
Dakine POV Camera Case
Dakine Trail Photo 33L Backpack
Dakine Sequence 33L Backpack
GoPro Gooseneck
Garmin VIRB Elite Dark Action Cam
GoPro HERO3/3+ Blackout Housing
Wasabi GoPro HERO3/3+ Dual Battery Wall, Auto Charger + 2 Batteries
Sony AS100 POV Action Cam
Sony AS100 POV Action Cam with Live View Remote
Subscribe to RSS Feed

Camera Gear

4 Item(s)

per page

Grid  List 

Set Descending Direction
Switch View
  • Bonehead Rev2 GoPro Helmet Mount

    Bonehead Rev2 GoPro Helmet Mount

    $40.00

    Bonehead Rev2 GoPro Helmet Mount.

    Learn More | Add to Wishlist | Add to Compare
  • Bonehead Rev2 Contour Rail Helmet Mount

    Bonehead Rev2 Contour Rail Helmet Mount

    $40.00

    Bonehead Rev2 Contour Rail Helmet Mount.

    Learn More | Add to Wishlist | Add to Compare
  • REvolve Contour Camera Mount

    REvolve Contour Camera Mount

    $60.00

    The REvolve Contour Camera Mount allows you to add the Contour series of cameras to the side of your helmet such as the Contour1080p, ContourGPS or Contour+. Bonehead Composites now offers a mounting solution for the contour camera and standard side mounts. Consists of a plastic Derlin plate and machined aluminum rail which slides into the contour rail guides and allows visor rotation and level adjustments. The REvolve Contour Camera Mount is sized per the shell/visor size. Select your REvolve size above when ordering. Note: Mount does not include Contour camera, which is available separately from ChutingStar.com. Mounting instructions 1. Remove original visor pin from the left side of the helmet. 2. Place a piece of masking tape over each raise mounting pad on the REvolve. 3. Using the longer pin supplied with the contour mount, slide the pin through the upper plate hole through the visor grommet and finally into the helmet and secure. 4. Rotate the plate, centering the middle or each lower mounting slots over the center of each mounting pad. Mark these locations with a pen and then check for center accuracy. 5. Using a 8/32 drill or Dremel tool drill the center marks through the helmet. 6. Secure the lower contour mount with supplied hardware with washers under both the screw head and nut. 7. Minor up/down adjustments can be obtain by loosening the lower screws and slightly rotating the plate to the fore or aft slot positions. Most sizes of the REvolve Contour Camera Mount are in stock for immediate shipment from ChutingStar.com.

    Learn More | Add to Wishlist | Add to Compare
  • Bonehead D-Box

    Bonehead D-Box

    $193.00

    Bonehead D-Box for the CX100/105/110/150 cameras.

    Learn More | Add to Wishlist | Add to Compare

4 Item(s)

per page

Grid  List 

Set Descending Direction
Switch View