ChutingStar Skydive & Skate Gear Superstore!
Looking for the Skate Shop?
GoPro HERO
Sony Action Cam Hard Lens Protector
Sony Action Cam Clip Head Mount Kit
UKPro GoPro 38HDF Floating Telescoping Camera Pole
UKPro GoPro 54HDF Floating Telescoping Camera Pole
Garmin VIRB Remote Control
GrellFAB GoPro PhantomX Front Mount
Aluminum GoPro HERO3+/4 Lens Ring
iPhone 6 Plus Wide Angle Death Lens
iPhone 6 Fisheye Death Lens
iPhone 6 Wide Angle Death Lens
Drift Stealth 2 Action Camera
Wasabi GoPro HERO4 1160mAh Battery
Wasabi GoPro HERO4 Dual USB Charger + 2 Batteries
Wasabi GoPro HERO4 Dual Battery Wall, Auto Charger + 2 Batteries
GoPro HERO4 1160mAh Rechargeable Battery
GoPro 3/3+/4 LCD Touch BacPac
GoPro HERO3 White Edition
GoPro HERO4 Dual Battery Charger + Battery
GrellFAB GoPro G3 Front Mount
Replacement Pivot Pad GoPro Upper Housings
GoPole GoPro EVO Floating Extension Pole + Remote Clip
GoPole GoPro REACH Extension Pole + Remote Clip
GoPro The Handler Floating Hand Grip
Subscribe to RSS Feed

Camera Gear

3 Item(s)

per page

Grid  List 

Set Descending Direction
Switch View
  • Bonehead AERO/Rev2 GoPro Helmet Mount

    Bonehead AERO/Rev2 GoPro Helmet Mount

    $40.00

    Bonehead AERO/Rev2 GoPro Helmet Mount.

    Learn More | Add to Wishlist | Add to Compare
  • Bonehead Rev2 Contour Rail Helmet Mount

    Bonehead Rev2 Contour Rail Helmet Mount

    $40.00

    Bonehead Rev2 Contour Rail Helmet Mount.

    Learn More | Add to Wishlist | Add to Compare
  • REvolve Contour Camera Mount

    REvolve Contour Camera Mount

    $60.00

    The REvolve Contour Camera Mount allows you to add the Contour series of cameras to the side of your helmet such as the Contour1080p, ContourGPS or Contour+. Bonehead Composites now offers a mounting solution for the contour camera and standard side mounts. Consists of a plastic Derlin plate and machined aluminum rail which slides into the contour rail guides and allows visor rotation and level adjustments. The REvolve Contour Camera Mount is sized per the shell/visor size. Select your REvolve size above when ordering. Note: Mount does not include Contour camera, which is available separately from ChutingStar.com. Mounting instructions 1. Remove original visor pin from the left side of the helmet. 2. Place a piece of masking tape over each raise mounting pad on the REvolve. 3. Using the longer pin supplied with the contour mount, slide the pin through the upper plate hole through the visor grommet and finally into the helmet and secure. 4. Rotate the plate, centering the middle or each lower mounting slots over the center of each mounting pad. Mark these locations with a pen and then check for center accuracy. 5. Using a 8/32 drill or Dremel tool drill the center marks through the helmet. 6. Secure the lower contour mount with supplied hardware with washers under both the screw head and nut. 7. Minor up/down adjustments can be obtain by loosening the lower screws and slightly rotating the plate to the fore or aft slot positions. Most sizes of the REvolve Contour Camera Mount are in stock for immediate shipment from ChutingStar.com.

    Learn More | Add to Wishlist | Add to Compare

3 Item(s)

per page

Grid  List 

Set Descending Direction
Switch View